マイクロ流体チップ内の電気浸透流の測定

From eDAQ Wiki
Revision as of 17:11, 26 May 2014 by Mori1240 (Talk | contribs) (電流をモニターすることによって電気浸透流(EOF)を測定します)

Jump to: navigation, search

非接触伝導度検出器を使ってマイクロ流体チップ内のチャネルに流れる電流をモニターし、 電気浸透流 ( EOF: electro-osmotic flow ) を測定しました。

はじめに

PDMS (ポリジメシルシロキサン) マイクロ流体チップ内の電気浸透流を、静電結合型の非接触電度計 (C4D: capacitively-coupled contactless conductivity)を使ってチャネルに流れる電流をモニターすることによって測定しました。測定データは eDAQのPowerChrom で記録し解析しました。ここで報告する方法は、従来のフューズトシリカチューブを使ったキャピラリー電気泳動を含め、様々なタイプのキャピラリー電気泳動測定にも応用できます。

この独創的な研究は Henry at the Department of Chemical and Biological Engineering, Colorado State University. qian.guan@colostate.edu の Qian Guan 及び Dr. Charles S 等によって実施されたものです。

使用した装置

  チャネル(流路)のサイズ: 長さ 4.75cm、幅 50μm、高さ 50μm

このアプリケーションでは ER280 PowerChrom システム、旧型の EA120 C4D アンプと ET121 プラットフォームを使いました。

測定条件

ここで紹介する測定データは、下記の測定条件で記録したものです:

  • 高電圧: +881 V
  • C4D 設定:
    • 周波数 = 500 kHz
    • アンプリチュード = 100 %
    • ヘッドステージゲイン ON

測定のセットアップ

C4D アンプからの出力 K シグナルをPowerChrom ユニットの入力1に接続します。PowerChrom ユニットの入力2で電流をモニターします。この二つのシグナルを PowerChrom ソフトウェアで連続的に表示させて記録します。

電流をモニターすることによって電気浸透流(EOF)を測定します

電流をモニターする方法で EOF を測定することに関しては以前に報告*しました。簡単に説明すると、一つのリザーバとチャネルに 20 mM のBGE を充填し、別のリザーバに 18 mM のBGEを入れます。最初のリザーバに+の高電圧を掛けると直ぐに電気浸透流が始まり、チャ ネル内の高濃度バックグランド電解溶液が徐々に低濃度バックグランド電解液に置き換わり、その結果チャネルの電気抵抗が増加します。印可した定電圧下でこのセパレーションカレントの変化をモニターします。カレントが定電流に達したら電位を反転させ、上の行程を反復させます。

  • Huang, X., Gordon, M. J., Zare, R. N., Anal. Chem. 1988, 60, 1837–1838)

カレントがプラトーに達するのに要した時間を等式1に代入してEOFを算出するのに使います。ここで、L は分離チャネルの長さ、V は総印可電圧、tはカレントがプラトーに達するのに要した秒単位の時間を表します。

           μEOF = L2/Vt 		Equation 1

Electro-osmotic Flow Measurement using the C4D

The microchip is set up for a close contact with the C4D microfluidic platform by spring screws. The desired detection point in the microchip channel is located at the center position between two detection electrodes on the surface of C4D microfluidic platform. The BGE loading and voltage control in this method is the same as that described in the current monitoring method and the two methods can be run at the same time.

It is generally recommend to use a microchip which has a bottom sheet with a thickness no higher than 0.5 mm, to obtain highly sensitive conductivity detection. Do not move or touch C4D microfluidic platform during experiments to avoid creating noise.

The time required to reach a sharp conductivity change from the beginning stable status is monitored using the C4D Amp. EOF is calculated based on Equation 2 where L’ is the distance between the reservoir where EOF starts flow and the detection point, and the other parameters are the same as those in Equation 1.

           μEOF = L’L/Vt		Equation 2 

Results

Figure 1 shows electropherograms for EOF measurements using both the current monitoring method (blue plot) and C4D (black plot).

The current monitoring method gives the average conductivity along the channel, as the channel is filled with the BGE of lower concentration. This produces a gradual decrease in the current monitor, until the whole channel is filled with the BGE of lower concentration, and a plateau is reached.

The C4D signal gives a conductivity measurement at a particular point along the channel, and thus there is a sudden decrease in conductivity, when the BGE of lower concentration reaches the position of the C4D electrodes.

Figure 2 shows the electropherogram of all the data, where the voltage is applied first in one direction, and then is reversed to make the EOF travel in the opposite direction along the chip’s channel. This is repeated a number of times.

Figure 1. Electropherogram for one run.
Figure 2. Electropherogram while voltage is alternated back and forth.