Difference between revisions of "E-corder"

From eDAQ Wiki
Jump to: navigation, search
Line 16: Line 16:
  
 
ポテンショスタットを使うには、e-corder と [http://www.edaq.com/ES260 EChem ソフトウェア] との組み合わせが最適です。e-corder には‘外部入力’ ( 電位波形シグナルを記録する) とアナログの‘レコーダ’ 出力が付いていますので、通常のポテンショスタットと同等の機能を持っています。
 
ポテンショスタットを使うには、e-corder と [http://www.edaq.com/ES260 EChem ソフトウェア] との組み合わせが最適です。e-corder には‘外部入力’ ( 電位波形シグナルを記録する) とアナログの‘レコーダ’ 出力が付いていますので、通常のポテンショスタットと同等の機能を持っています。
ポテンショスタットに‘外部入力’ が無くても,e-corder を使ってシグナルが記録できます。使用するポテンショスタットに‘レコーダ’、もしくは‘モニター’出力が付いてれば対応します。
+
ポテンショスタットに‘外部入力’ が無くても,e-corder を使えばシグナルを記録できます。使用するポテンショスタットに‘レコーダ’、もしくは‘モニター’出力が付いてるいことを確認してください。
  
If your potentiostat is presently used with a conventional chart recorder, XY plotter, or oscilloscope, it will almost certainly be suitable for connection to e-corder.
+
現在ポテンショスタットにチャートレコーダや、XYプロッター、オシロスコープを使って測定している場合は、問題無くe-corderに接続できます。
  
 
The e-corder connects to potentiostats from the following manufacturers:
 
The e-corder connects to potentiostats from the following manufacturers:

Revision as of 16:10, 12 February 2014

Figure 1. e-corder with PAR362
Figure 2. e-corder with Hokuto Denko potentiostat
Figure 3. e-corder with Pine AFRDE4

e-corder とEChem ソフトウェアを使っ、て市販のポテンショスタットで記録することができます

eDAQ 社製ポテンショスタット:


eDAQ社のe-corderは波形ジェネレータ機能を持ったデータレコーダです。eDAQでは各種オリジナルポテンショスタットを発売していますが、他社製品のポテンショスタットにも対応します。

ポテンショスタットを使うには、e-corder と EChem ソフトウェア との組み合わせが最適です。e-corder には‘外部入力’ ( 電位波形シグナルを記録する) とアナログの‘レコーダ’ 出力が付いていますので、通常のポテンショスタットと同等の機能を持っています。 ポテンショスタットに‘外部入力’ が無くても,e-corder を使えばシグナルを記録できます。使用するポテンショスタットに‘レコーダ’、もしくは‘モニター’出力が付いてるいことを確認してください。

現在ポテンショスタットにチャートレコーダや、XYプロッター、オシロスコープを使って測定している場合は、問題無くe-corderに接続できます。

The e-corder connects to potentiostats from the following manufacturers:

  • AMEL
  • BANK Elektronik
  • BAS (Bioanalytical Systems)
  • Cypress Systems
  • EMS
  • HEKA
  • Hokuto Denko
  • PINE Instruments
  • Princeton Applied Research (was EG&G PAR)
  • Radiometer
  • Schlumberger
  • Sycopel


For more information, please refer to the EChem software manual, available after following the Manuals link at the eDAQ help page. Chapter 3 describes how to connect the e-corder to a potentiostat and how to set up the EChem software. Chapter 8 presents specific examples of third party potentiostats compatible with the e-corder.