Difference between revisions of "Signal Sources and Amplifiers"

Revision as of 12:11, 14 September 2013

Introduction

In order to record an experimental signal with high fidelity 3 issues need to be considered.

• Signal Sources to be measured
• Characteristics of the signal sources
• Type of Amplifier used to record the signal

Signal Sources

There are 4 types or classes of electical signal sources which occur in various experimental situations. It is important to understand the characteristcs of these signal sources in order that they can be matched to the correct amplifier/recording system without degrading the accuracy of the measurement.

PLEASE NOTE: In discussing the characteristics of signal sources reference will be made to "Source Impedance" which in its most general form consists of a combination of 3 electrical elements: Resistance,Inductance and Capacitance. In most cases one of these elements will predominate, most commonly resistance. So when the term "Source Resistance" is used it implies that the impedance of the source is mainly resistive in nature. At DC or low frequencies source impedance is mainly resistive and the other elements, capacitance and inductance only come into play at higher frequencies.

http://en.wikipedia.org/wiki/Electrical_impedance

These 4 classes are listed and discussed below:

Single ended - Floating

Single Ended Floating signals appears between the two terminals of the signal source neither of which is connected to ground. This signal can either be a voltage source or a current source.

An ideal voltage Source has a near zero internal impedance. An accurate reading can only be obtained with a measuring circuit whose own internal resistance is much higher than the source resistance of the source. Voltmeters therefore need to have a high internal reistance - ideally infinite.

An ideal current Source has a near infinite internal impedance. In this case to measure the source current the measurement impedance should be very low. Ammeters therefore need to have a low internal resistance - ideally zero.

Here is a picture:

Examples of Single Ended Floating Sources

Voltage sources

• Battery - very low internal resistance
• pH cell - very high internal resistance
• Thermocouple - very low internal reistance

Current sources

• Silicon detector - high internal reisitance
• Electrochemical sensor - high internal resistance
• Piezo-Electric sensor - very high resistance

Single ended - Grounded with Common mode voltage

In this configuration one of the terminals is effectively connected to ground via another signal source - called a "Common Mode Voltage". This CM Voltage may be intentional but in most cases it is unintentional and can present a significant problem in the measurement of the signal of interest. In this case the effective signal occurs across the two terminals of the source and is made up of the signal with the CM voltage added to it as shown below. A special but common case of this configuration is when the CM voltage is zero and one of the terminals is effectively connected to ground.

Add picture of single ended with common mode voltage.

Examples of Single Ended Grounded with common mode

• AC Line powered signal generator
• Resistive shunt for measuring current
• AC powered transducer
• Chromatography detector

Balanced - Floating

In this configuration the two terminals are both active and have equal impedance to a common point which is floating and unconnected to ground. The voltage on the two terminals moves in different directions in relation to the common point.

Add picture of single ended with common mode voltage.

Examples of Balanced floating Source

• Four Arm Wheatstone Bridge with floating power supply
• Linear variable differential transformer (LVDT)
• Center tapped Transformer

Balanced - Grounded with Common mode voltage

In this configuration the two terminals are both active and have equal impedance to a common point which is connected to ground via a CM voltage. The voltage on the two terminals moves in different directions in relation to the common point. The CM votage can either be Zero when the center point is directly grounded, it can be at a fixed DC value or can result from unintentional connection to ground.

Add picture of single ended with common mode voltage.

Examples of Balanced floating Source with coomon mode voltage

• Four Arm Wheatstone Bridge with line powered supply
• Differential output Operational Amplifier

Source Characteristics

• Source Impedance
• Source Voltage
• Source Frequency content

Amplifier types

• Single ended - Grounded
• Single ended - Isolated
• Balanced - Grounded
• Balanced - Isolated